Exactly How to Remove and Change a Bathtub
Exactly How to Remove and Change a Bathtub
Blog Article
What are your ideas on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub and also embeded in the brand-new one. Make certain you have actually certified on your own for the work and are comfortable attempting it. Rather than working with a specialist to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This post will assist you set up a new tub in your restroom if you have already bought a new bathtub and also do not require to transform the setup of your previous water pipes.
Your tools and material checklist should consist of the following:
Planning for the Setup
Firstly, the sustaining structure provided with the bath should be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently prepare to be fitted in its last setting.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited accessibility that is usually the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any old securing substance.
Prior to going on to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub until the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable tap connector to the proper supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water supply as well as inspect all joints and also brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bath tub has been used at least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, causing problems with wetness as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly readily available on the market. It is suggested to fit the tiles making use of water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate person who reads about Installing A Bathtub, I imagined sharing that piece of content was a smart idea. Loved our entry? Please share it. Let somebody else discover it. Thank-you for your time invested reading it.
Get A Free Quote
Report this page